Bathroom Demolition

Original bath

Demolishing the shower was not easy. The mortar bed that they installed in some places was over an inch thick. It was dry as a bone after 40 years. The tiler on this job did not get any call-backs I believe.

The amount of weight all of the mortar adds is incredible. The new materials will be a lot lighter.

There's at least one layer of wallpaper that's been painted over so all of the drywall has to go.

Behind the shower wall you can see the roof line of the first floor. (note the angled section). This wall gets really hot from the exterior. This will get another 2" of rigid foam insulation before the shower goes back in.

Sanitary waste and vent stack

I don't have the heart to smash the cast iron tub with a sledgehammer, so it stays.

That bundle of wires is heading down to the panel box. The new code doesn't allow any plumbing to be above any electrical.

Hot & cold water supplies

All the plumbing behind the walls is in good shape.

Bathroom Renovation

The seventies called...they want their bathroom back. They can have it.

This bathroom has been pretty grody since the day we moved in even after I re-caulked the tub and replaced the toy sink they had installed.
The floor is unlevel and there is a hole in the wall near the tub. It's pitiful.
Yesterday I bought some new tile and today I began the demolition.

I've yet to determine if the tub is cast iron or steel and though I would like to remove it I'm not sure it's going to be feasible.

I had always assumed that the existing tile was laid over another floor. Today I found out that the original tile was removed but the original mortar bed was left in place and then built up on top of it. The bathroom floor was alway higher than the hall floor. It's why it was so uneven and very heavy. There was so much weight that I believe the floor was sagging. It is very, very squeaky in the hall outside the bath.

Anyway, under the old mortar was the metal lath that was always used for tile floors back in the day. Apparently there are some who are still using this system, but no so much in the South. The subfloor isn't in too bad a condition for it's age though you can see there has been some moisture here and there.

It's been a while since I've remodeled a bathroom and these days there are way more products out there than there was back then. It's really a matter of who's technique you choose to go with. I'm still trying to decide.

Walnut threshold

The photo shows the 8/4 walnut stock that I used to make the threshold for the patio door. The piece on the right is the actual part that I fabricated from the larger stock on the left.

It's a fairly hard wood but not difficult to work at all. Not super hard like the exotics from Brazil or Africa. And it's domestic which I believe is a better way to go. Cost $70.

Walnut is a common wood for gun stocks. This is american walnut as opposed to black walnut which is denser and more expensive. It's more coveted as well.

The table saw was the only tool I needed to make the piece. It took about half a day to get everything ripped down and shaped. It is basically an L shaped piece.

Threshold profile

I used a mixture of 30% sparr urethane and 70% Teak oil to finish the piece. It came out very nice and so far is repelling the water very nicely. Nice vid here. Thanks Izzy!

There was an inch and quarter gap between the deck and the door sill that needed to be filled in. I found some pavers that fit perfectly in the space but I didn't have enough to do the job and I couldn't find any more of them anywhere. I was at The Stone Center looking for the pavers when the guy said he had a solid piece the right thickness.

Walnut threshold and sandstone sill

There was lots of sandstone that was the right thickness but none were long enough. I needed about 64" x 5" to fill the gap. I ended up getting about a 30" long piece that was 18" wide for $20. I had to buy a diamond blade for the circular saw to rip the stone down to 5" pieces.

I had not sawn stone before and it wasn't too difficult with the new blade. I wet the stone down every minute or two. The job went better than I anticipated. The weakest part is the joints where I used some colored mortar to join the pieces. I've never laid a brick in my life so I didn't have the slightest idea how to make the joint. It's alright though, maybe not perfect.

Solar powered lights

New door

The soffit is replaced the fascia is up, everything is caulked and painted now.

We also added an exterior flood light and an outlet that is solar powered as well.

Old window

It's good to be utilizing the door now. It's very convenient and beats walking through the garage to get to the deck. At night the glass allows the light from inside to illuminate the deck and so it helps out with the outside lighting as well.  It's very quiet as well. The music can be fairly loud inside and you do not hear anything thru the door whatsoever.

I'm very happy with it.

Solar

I have finally completed the PV/Battery Backup system. It's been in progress for sometime, but I wanted to wait until it was finished to mention it.

The two panels on the left are Suniva 250 watt each. I used Ironridge rails for mounting.

The panels are charging two 246 amp hour GS batteries. Huge batteries!

The charge controller is the 24v Xantrex C60. No bells and whistles but cost effective and reliable, so far.

I have a 300W Samlex inverter, which is mounted above ceiling in the attic.

When I pulled all of the sheetrock down in the dining room I dedicated one duplex outlet to the solar system. So instead of it being wired back to the breaker box like the others, I took it's wiring above ceiling into the garage and wired a plug to the end. It plugs into the inverter.

If there is a power failure, I can plug into the solar outlet inside the house.

On the right is the breaker box by Midnite solar which houses the guts of the system. In a future post I will go over all of the components in the box.

As of yet I haven't really put the system through it's paces. Just some small loads like charging cell phones and laptops. There is a motion activated floodlight on the back deck that is now wired into this system as well. The flood load is also small with two led bulbs and only a 5 minute time setting when it detects motion.

DC Breaker Box

Battery box w/ GS Batteries

On sunny days, now during late spring, the charger is topping up the batteries by noon usually. At some point I am planning on wiring in the lighting in the dining room onto this system which are 8 dimmable led's that run just a few hours per day, normally dimmed at night. It will be nice to have this lighting available in case of grid power going down.



Electrical enclosure with Xantrex charge controller in the picture above. On the right the battery box with the (2) GS246 wired in parallel for 24v.

Rip-off

You might ask why we go to all the trouble to add so many energy efficient products to the house. Well, when you are beholden to Georgia Power for your electrical service you've got to cut costs wherever you can because they certainly won't.

With the Nuclear Construction Cost Recovery fee that the Public Service Commision allowed we are pre-paying for Southern Company's new nuclear plants at Vogtle.

So our bills are up 6.5%, there are already cost overruns with the construction and we will certainly shoulder any additional costs in the future. The fee percentage goes up each year, so our bills will be higher again next year.

I thought more supply meant lower prices...

French Door

The door really gives the room a more spacious feel, which I wasn't really expecting. It swings out so it suppose to resist wind and being kicked in. Actually the more exterior pressure exerted the tighter it seals. Aesthetically it's really cool. Lots of light and the open quality of the room increased exponentially. It fits.

Integrity Wood Ultrex Outswing French Door by  Marvin, outswing double patio door, $2220, delivered.

Low E 272 w/Argon
SHGC .24
U Value - .30
VT - .40

Bye bye window!

Today our door from Marvin arrived. It will be an outswing french door that will replace the two double hung windows that are there now.

Before the deck was built this window was about six feet up. There was a small amount of demolition to do with the brick beneath the window.

An entry door will be an improvement from having to walk into the garage to access the deck. It will also be a thermal improvement over the two heinous single pane windows that leak air terribly and won't open and close anymore because someone painted them shut. Lovely!

Hole in the wall

I can always count on finding an example of shoddy workmanship every time I remove something and this time was no exception. When the hvac register was installed they cut all the way through the exterior gyp board as you can see on the left. They also hacked up the rim joist and sill.

So for the last 30 yrs hot and cold air has basically been venting to the exterior. Not that the gyp board provides much R value, but it's at least an air barrier. This probably means the registers on the other side of the room could be the same way. I demo'd this register and it's duct back to the y fitting and capped it off.

Cutting the brick turned out to be easier than I expected. I bought a 6" masonry cutting disc and installed it on my angle grinder. It made a lot of dust but wasn't real hard to grind thru the bricks at all. No water necessary. It only took about an hour to demo the entire section.